FEP tube with a 0.4mm ID that has been flanged to a very specific diameter.
Find out more about Tipping & Flanging Fluoroplastics.
FEP tube formed into a retractable coil. This is used within an auto-sampler.
Find out more about Retractable Coils.
Thick PTFE sheet cut using laser technology. The box was punched and scored to create the 3D profile.
Find out more about Thermoforming & Manipulation of Fluoroplastics.
Free issue PTFE machined parts that have been chemically etched to enable bonding. Only the area to be bonded has been chemically etched.
Find out more about Etching Fluoroplastics.
Selection of covers made from FEP heat shrink to encapsulate level detection probes.
Find out more about FEP Probe Covers.
Free issue conical springs encapsulated with thick PTFE, sealed at each end and spark tested to ensure chemical resistance.
Find out more about Encapsulating with Fluoroplastics.
Sample bag made from Tedlar® Film and used for gas, odour and automotive emission sampling for VOC’s.
Find out more about Tedlar® Gas Sample Bags.
Shatterproof lamp coated in FEP tube with a welded seal and a heat shrinkable end section to ensure the seal over the end cap. All our coated lamps are IEC 61549 compliant for use in glass free environments.
Find out more about Shatterproof Lamps.
Retractable coils from 0.8mm ID x 1.6mm OD FEP tube. The ends have been flanged to a controlled diameter and free issue fittings and markers have been applied during the coiling process.
Find out more about Retractable Coils.
PTFE inkjet tube is supplied as a natural tube with a coloured identification stripe along the length. The tubes are usually assembled into an umbilical, together with the relevant electronics, and are either sleeved with a heat shrink outer or more commonly an over extrusion.
Find out more about PTFE Tubes.
19mm ID FEP tube with a 1.5mm wall was reduced in diameter to 8mm to restrict the flow in a specific area. It then needed to taper back up to the original ID. For use in a fluid handling application.
Find out more about Fluoroplastics Tubing Assemblies.
FEP Tube 0.6mm ID x 0.2mm wall reformed with a reduced tip to 0.25mm ID. FEP tapered tips are delivery tips for a medical application and small batch sizes were required.
Find out more about Thermoforming & Manipulation of Fluoroplastics.
PTFE sleeve AWG 15L (TW15) pigmented white and supplied with a moulded collar section at one end with a nominal OD of 3mm.
Find out more about Fluoroplastic Tubing Assemblies.
FEP and PTFE tubes have been preformed to our customers' requirements, using thermoforming techniques.
Find out more about Fluoroplastic Tubing Assemblies.
Medical grade closed end heat shrinkable FEP tube. The thickness of the tip was critical as this was used with microwave technology to treat various forms of cancer.
Find out more about Welding & Sealing Fluoroplastics.
Plugged PTFE prove covers made from PTFE tubing and terminated with a welded plug. The probe covers are manufactured from moulded, machined or welded PTFE without any metal internal support.
Find out more about Plugged PTFE Probe Covers.
Rectangular profile FEP tubes made using a re-forming technique.
Find out more about Thermoforming & Manipulation Fluoroplastics.
PTFE tube has been cut to a specific length and then dip etched on the ID & OD so that they can be bonded into place.
Find out more about Etching Fluoroplastics.
FEP heat shrinkable roll covers applied to metal rollers using a simple hot air gun.
Find out more about Roll Covers.
Thermowells coated in FEP shrinkable tubing and a PTFE spray coating for use in hostile conditions.
Find out more about Thermowell & Sensor Probe Coating Service.
Type K thermocouple encapsulated along the full length with FEP heat shrink and sealed at one end to prevent chemical ingress.
Find out more about Thermowell & Sensor Probe Coating Service.
Free issue thermometers encapsulated with FEP heat shrink and sealed at each end so that they are shatterproof for glass free environments.
Find out more about Encapsulating with Fluoroplastics.
Flexible connectors are used in chromatography instruments for separation, purification and concentration of target compounds. The thin walled PTFE sleeving is moulded within the silicone section.
Find out more about Medical Fluoroplastics.
Multi-lumen PTFE tube can be supplied with multiple internal diameters, and allows a different medium, such as fluids or guide wires, to pass along each ID. Predominantly used in medical devices.
Find out more about Medical Fluoroplastics.
Bellows welded from vacuum formed sections of 50-micron FEP film.
Find out more about Welding & Sealing Fluoroplastics.
50-micron FEP film vacuum formed and welded with kapton reinforcement to make an insulating cover for a pacemaker application.
Find out more about Welding & Sealing Fluoroplastics.
Extruded spiral binding in PTFE used for harness applications.
Find out more about Fluoroplastic Tubing.
Extruded tubing profiles were made to our customer’s design, they were to push over a profile and into a channel offering a chemically inert and non-stick seal.
Find out more about PTFE Tubing.
Sample bag made from FEP film and used for odour sampling and applications where a very low ppm are involved.
Find out more about FEP Gas Sample Bags.
Human breath bag enclosed within a specially designed and screen-printed PVC outer.
Find out more about PVC & PU Gas Sample Bags.
We can offer closed end FEP tubes and heat shrinkable FEP tubes for medical and chemical applications. We can tightly control the thickness of the tip.
Find out more about FEP Tubes.